2017+ Chrysler Pacifica Minivan Forums banner

1 - 8 of 8 Posts

·
Registered
Joined
·
40 Posts
Discussion Starter #1 (Edited)
I need to replace my right mirror, can you help with the procedure please Lily
 

·
Super Moderator
Joined
·
562 Posts
REMOVAL AND INSTALLATION
REMOVAL



  1. Position the door glass in the up position.
  2. Remove the door trim panel (Refer to Body/Door - Front/PANEL, Door Trim/Removal and Installation).
  3. Disconnect the wire harness connectors (1).
  4. Open the access cover (2).
  5. Unseat the rubber grommet (3) and insert through the carrier plate.

  6. Disconnect the wiring harness routing clips.
  7. Remove the two lower outside rearview mirror nuts (1).
  8. Position the door glass in the fully lowered position.
  9. Remove the one upper outside rearview mirror nut (1).

  10. Remove the outside rearview mirror (1).
  11. Route the wiring harness (3) through the door opening (2).
  12. Remove white plastic assembly aid from the top forward hole in the door opening.
INSTALLATION


  1. Route the wiring harness (3) into the door opening (2).
  2. Position the outside rearview mirror (1) onto the vehicle.

  3. Install the one upper outside rearview mirror nut (1) and tighten to the proper (Torque Specifications).
  4. Raise the door glass to fully up position.
  5. Install the two lower outside rearview mirror nuts (1) and tighten to the proper (Torque Specifications).

    NOTE
    To prevent contact with the door glass, be certain to route the wiring harness forward of the front window channel.

  6. Secure the wiring harness routing clips.


    NOTE
    The rubber grommet must face rearward on the door to prevent interference with the door trim panel installation.

  7. Insert the rubber grommet (3) through the carrier plate and seat fully.
  8. Close the access cover (2).
  9. Connect the wire harness connectors (1).
  10. Install the door trim panel (Refer to 23 - Body/Door - Front/PANEL, Door Trim/Removal and Installation).
TORQUE SPECIFICATIONS

DESCRIPTIONN·mFt LbsIn LbsCOMMENT
Exterior mirror fasteners980
Fender to body bolts980
Fender to fascia bolts653
Front fender bolts980
Front door armrest pull cup fastener871
Front door carrier plate bolts871
Front door glass fasteners1310
Front door hinge bolts - body4332
Front door hinge bolts - door2418
Front door interior handle fasteners4.540
Front door latch bolts871
Front door latch striker bolts2418
Front door trim panel interior handle bolt762
Front door trim panel pull handle bolt762
Front seat bolts6548
Front seat armrest bolt2518
Hood hinge to body bolts118
Hood hinge to hood nuts2216
Hood striker bolts1612
Instrument panel carrier bolts129
Instrument panel cowl bolts2015
Instrument panel dash bolts653
Liftgate hinge to body bolts 2518
Liftgate hinge to liftgate bolts 1813
Liftgate latch bolts 107
Liftgate striker bolts2720
Second row center seatback bolts5541
Second row stow-n-go armrest bolt2518
Second row stow-n-go seat bolts6850
Second row stow-n-go seat nuts5843
Sliding door carrier plate bolts871
Sliding door center hinge to door fasteners1310
Sliding door center roller to bracket fasteners980
Sliding door center track fasteners762
Sliding door front latch bolts980
Sliding door glass fasteners1310
Sliding door ground wire fastener107
Sliding door inner handle fasteners1310
Sliding door latch striker bolts - front2418
Sliding door latch striker bolts - rear2418
Sliding door lower glass channel to door bolts871
Sliding door lower hinge to drive unit bolt762
Sliding door lower track fasteners1310
Sliding door open latch to b-pillar107
Sliding door stabilizer fasteners - door side653
Sliding door to lower track bolts1310
Sliding door upper track fasteners871
Sunroof glass panel attachment screw4.540
Sunroof to body bolts762
Third row headrest nuts2518
Third row seat bolts5440
Third row seat recliner bolts6548
 

·
Super Moderator
Joined
·
562 Posts
REMOVAL AND INSTALLATION Door Trim Panel
REMOVAL



  1. For PHEV vehicles, power down the 12-volt system (Refer to 08 - Electrical/Standard Procedure).
  2. Disconnect and isolate the negative battery cable. If equipped with an Intelligent Battery Sensor (IBS), disconnect the IBS connector first before disconnecting the negative battery cable.
  3. Remove the window switch assembly (Refer to 08 - Electrical/Power Windows/SWITCH, Power Window/Removal and Installation).
  4. Using a small flat bladed tool or equivalent, remove the pull cup trim mat (1).

  5. Remove the bolt (1).

  6. Using a small flat bladed tool or equivalent, remove the trim cover (1).

  7. Remove the bolt (1).

  8. Using special tool
    Remover, Trim

    Remover, Trim
    Click to Enlarge​
    , separate the 12 attachment fasteners (1).


  9. Separate the trim panel assembly (1) from the door (2).

  10. Disconnect the trim panel wire harness connectors.
  11. Disconnect the interior handle cables (1) and remove the trim panel assembly.
INSTALLATION




NOTE
Prior to installing the door trim panel, replace any trim panel retaining clips that may have been damaged during the removal process.


  1. Connect the interior handle cables (1) and connect the trim panel wire harness connectors.

  2. Position the trim panel assembly (1) back onto the door (2).

  3. Seat the 12 attachment fasteners (1) fully.

  4. Install the bolt (1) and tighten to the proper (Torque Specifications).

  5. Install the trim cover (1) and seat fully.

  6. Install the bolt (1) and tighten to the proper (Torque Specifications).

  7. Install the pull cup trim mat (1) and seat fully.
  8. Install the window switch assembly (Refer to 08 - Electrical/Power Windows/SWITCH, Power Window/Removal and Installation).
  9. For PHEV vehicles, power up the 12-volt system (Refer to 08 - Electrical/Standard Procedure).
  10. Connect the negative battery cable. If equipped with an Intelligent Battery Sensor (IBS), connect the IBS connector to the negative battery cable.
 

·
Super Moderator
Joined
·
562 Posts
REMOVAL AND INSTALLATION Window Switch
REMOVAL

SWITCH-DRIVER DOOR



  1. Disconnect and isolate the battery negative cable.
  2. Using a pry tool, gently remove the switch assembly (1) or the vent window switch (2) from the door trim panel.
  3. Disconnect the electrical connectors.
SWITCH-PASSENGER DOOR


  1. Disconnect and isolate the battery negative cable.
  2. Using a pry tool, gently remove the switch assembly from the door trim panel.
  3. Disconnect the electrical connector.
SWITCH-SLIDING DOORS


  1. Disconnect and isolate the battery negative cable.
  2. Using a pry tool, gently remove the switch assembly from the door trim panel.
  3. Disconnect the electrical connector.
INSTALLATION

SWITCH-DRIVER DOOR



  1. Connect the electrical connectors.
  2. Firmly snap the switch assembly into the door trim panel.
  3. Connect the battery negative cable.
SWITCH-PASSENGER DOOR


  1. Connect the electrical connectors and install the switch.
  2. Firmly snap the switch assembly into the door trim panel.
  3. Connect the battery negative cable.
SWITCH-SLIDING DOORS


  1. Connect the electrical connectors and install the switch.
  2. Firmly snap the switch assembly into the inside door handle.
  3. Connect the battery negative cable.
 

·
Registered
Joined
·
40 Posts
Discussion Starter #5
Thanks, someone clipped my mirror in a parking lot and I am going to have to replace it. It is supposed to be here on Friday. I went ahead and took the door panel off and put it back to familiarize myself with it. It was very easy. Took me literally 5 minutes to get it off. The dealership (truly the stealership in this case) said they want $200 just for the labor. It will liters take me 30 minutes, max to do this in my garage.

Thanks for the help Lily!
 

·
Registered
Joined
·
143 Posts
I need to replace my right mirror, can you help with the procedure please Lily
can not tell what the "painted base" is from the descriptions or the diagram for this 2018 Chrysler Pacifica Power Mirror. Decent cost difference.
Links to Mopar part pages via part numbers below.
5VD36KBXAE Man Fold, W/O Painted Base, W/Blind Spot, Jazz Blue
5RM14KBXAE Man Fold, W/Painted Base, W/Blind Spot, Jazz Blue

The diagram image is identical for both parts and there is no indication of what the base is.
 

·
Super Moderator
Joined
·
562 Posts
can not tell what the "painted base" is from the descriptions or the diagram for this 2018 Chrysler Pacifica Power Mirror. Decent cost difference.
Links to Mopar part pages via part numbers below.
5VD36KBXAE Man Fold, W/O Painted Base, W/Blind Spot, Jazz Blue
5RM14KBXAE Man Fold, W/Painted Base, W/Blind Spot, Jazz Blue

The diagram image is identical for both parts and there is no indication of what the base is.
no idea, probably going to have to ask the parts department at the dealership.
 
1 - 8 of 8 Posts
Top